Brushable Polyurea


[Home] [Catalog of Products] [Where to Start] [[Bonding Systems] [Chip Floors] [Chemical Resistance]
[Coatings] [Conductive] [Applications] [Elastomeric Systems] [High Temperature]
[Industrial Floors] [Injection] [Joint Systems & Sealants] [Mortars / Grouts] [Novolac] [Polymer Systems]
[Primers and Sealers] [Misc.] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Installation Tips]
[Product Guide] [Wood Filler] [Who We Are] [Guide Specs]
[Tech Data Sheets in Acrobat Format ] [MSDS in Acrobat Format] [Online Ordering Authorization Form]

 

Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980


Epoxy.com Product #1800

Fast Setting Brushable Polyurea Coating


DESCRIPTION
Epoxy.com PRODUCT #1800 Fast Setting Brushable Polyurea Coating
is a two component brushable aliphatic polyurea. It cures in minutes to provide a tough chemical and abrasion resistant coating. This reaction is very fast, with typical working times of less than 15 minutes. PRODUCT #1800 is recommended for use in areas such as tanks, cooling tower linings, water and wastewater and waterproof deck coatings. It can be used in food and beverage cold storage areas, mechanical rooms, industrial plants, chemical and fertilizer plants, pulp and paper mills and petrochemical facilities.

ADVANTAGES

bulletFast cure. Can be mixed and put in service within 2 hours.
bulletChemical resistant
bullet100% solids. Two-component, low shrinkage
bulletExcellent physical properties including high adhesion, tensile strength and abrasion resistance.
bulletHigh thermal stability at temperatures up to 350°F.

PHYSICAL PROPERTIES

Mix Ratio By volume 1:1
Cured Properties  
Gel time, minutes 20
Surface at 30 minutes tacky
Surface at 2 hours tack free
Full Cure 5 days
Shore D Hardness, 65
Tensile strength, psi 3200
Elongation, % 60%
Tear strength, psi 310
Remains flexible in temperature range of
     -45°F to 200°F
     1000g 1000 rev CS-17
 
< 5 mg.
Flash Point, Components > 200°F
Flexibility Testing
     (1/32" steel panels)
> 160 in-lbs
Gardner Impact Direct and Indirect
Moisture Vapor Transmission 0.025 perm
     ASTM E 96  
Abrasion Resistance (wt. loss mg)
     ASTM D 4060
     1000g
 
1000 rev H-18 200mg.
Color Medium Gray - Stock Color
(White, Black, Light Gray, Dark Gray, Beige, Brick Red, Safety Yellow by special order minimum quantities required)
Bond Strength
     Concrete
     Steel
     Wood
     (Wood delamination)
375 psi
1,750 psi
200 psi

 

SURFACE PREPARATION

bulletSteel Surfaces - Prepare in accordance with Steel Structures Painting Council Surface Preparation SSPC-SP6 to SP10 near-white metal blast cleaning. All work blasted should be coated the same day. Recommended primer on steel is Epoxy.com Product #1200 - Epoxy Zinc Rich Primer.
bulletNew concrete - remove laitance by acid etching, abrasive blasting or water blasting. Old concrete - abrasive blast or water blast to remove laitance and contamination.
bulletPolyurea - Less than three days old solvent wipe and apply PRODUCT #1800; if more than 3 days old roughen surface with abrasive sanding. Solvent Wipe with Acetone or MEK and apply.
bulletProject Conditions: Surface must be structurally sound, dry, and uncontaminated. Concrete must be free of voids, bugholes, honeycombs and delaminations.

MIXING: PRODUCT #1800 is a plural component polyurea system. Equal volume parts of the Part A resin and Part B hardener should be mixed in small 1 pint batches. Always add the Part B hardener to the Part A resin.

APPLICATION:

Epoxy.com PRODUCT #1800 may be applied by brush, roller or squeegee. Concrete surfaces shall be primed with EpoxySystems Product # 810 Primer. Apply PRODUCT #1800 to achieve the required mil thickness with 50% overlaps. Aggregate broadcast may be applied if non-skid surface is required.

PRODUCT #1800 can be applied at temperatures from 35°F to 120°F. Apply to achieve the required mil thickness with 50% overlaps.

PACKAGING: PRODUCT #1800 is packaged as a 2 gallon unit and 10 gallon unit.

LIMITATIONS: PRODUCT #1800 is an alphatic based polyurea system. Consult chemical resistant chart for corrosive environment applications. Do not install in hydrostatic or moisture/vapor conditions.

SHELF LIFE: Six months minimum when stored at 75°F and dry conditions. PRODUCT #1800, like most construction materials, must be stored in a dry, well protected and suitable storage environment. Keep containers sealed.

CAUTION: Contains aliphatic isocyanates. Avoid breathing vapors. Avoid contact with skin and eyes. Do not ingest. Keep away from foodstuffs and wash thoroughly before smoking or eating. Should skin contact occur, wash skin well with soap and water. Should eye contact occur, flush thoroughly for at least 15 minutes with water. Get medical attention.

FOR INDUSTRIAL USE ONLY. KEEP AWAY FROM CHILDREN.

Hit Counter

Exclaim

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over 300 products,
Since 1980
Florida & Vermont
USA

Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.

321-206-1833   Customer Service - Ordering and Order Status
                          Katey Fontaine, VP - Customer Service Director
                          sales@epoxy.com

714-657-3826  Technical Support
                         Norm Lambert, President - Technical Support Director 
                         info@epoxy.com
  
352-489-1666   Accounting and Administration
                          Debby Lambert, CEO, and CFO
                          office@epoxy.com 

352-489-1625   Fax line to all Departments
                         www.epoxy.com

24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253

MasterCard, Visa, and American Express logo

Copyright © 1994-2009 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.

This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.

Epoxy.com a division of Epoxy Systems, Inc.  warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months;  Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight  Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days.   Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com  within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com  SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.

Many of our products are made on an individual order basis.   Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater.  No returns on non-list priced items.  All Returns are for merchandise (store) credit only, no cash or credit card credits.  In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.

 

[Home] [Catalog of Products] [Where to Start] [[Bonding Systems] [Chip Floors] [Chemical Resistance]
[Coatings] [Conductive] [Applications] [Elastomeric Systems] [High Temperature]
[Industrial Floors] [Injection] [Joint Systems & Sealants] [Mortars / Grouts] [Novolac] [Polymer Systems]
[Primers and Sealers] [Misc.] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Installation Tips]
[Product Guide] [Wood Filler] [Who We Are] [Guide Specs]
[Tech Data Sheets in Acrobat Format ] [MSDS in Acrobat Format] [Online Ordering Authorization Form]


Hit Counter

 

Secure Login