Epoxy Mortar


[Home] [Catalog of Products] [Where to Start] [[Bonding Systems] [Chip Floors] [Chemical Resistance]
[Coatings] [Conductive] [Applications] [Elastomeric Systems] [High Temperature]
[Industrial Floors] [Injection] [Joint Systems & Sealants] [Mortars / Grouts] [Novolac] [Polymer Systems]
[Primers and Sealers] [Misc.] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Installation Tips]
[Product Guide] [Who We Are] [Guide Specs]
[Tech Data Sheets in Acrobat Format ] [MSDS in Acrobat Format] [Online Ordering Authorization Form]

 

Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980  

                                                   


Epoxy.com™ Product #19

Epoxy Binder and Mortar System


This technical data sheet is for reference only.  Its new stock numbers are Product #24 (pigmented) and Product #28  (clear).

GENERAL DESCRIPTION

Product #19 is a multi-function liquid applied, 100% solids epoxy binder and mortar system with excellent wear, and chemical resistance. Product #19 is an excellent general purpose material with excellent clarity and color retention. It is essentially odorless and so it can be used in occupied areas.

 

APPLICATIONS

Any place where a high strength, durable, mortar is required.

 

ADVANTAGES

  • LOW ODOR
  • STRONG YET RESILIENT
  • VARIABLE SURFACES FROM NON-SLIP TO SMOOTH
  • ABRASION RESISTANT
  • LOW VISCOSITY - GOOD WETTING PROPERTIES
  • AVAILABLE IN "FAST CURE" SYSTEMS
  • MEETS USDA STANDARDS FOR USE IN FOOD HANDLING APPLICATIONS
  • GOOD TROWELING PROPERTIES

 

SURFACE PREPARATION

Surface must be clean and sound. Remove all dirt, laitance, grease curing compounds and other foreign matter by sandblasting, mechanical abrasion. If acid etching is used follow with abrasive or mechanical abrasion. Remove water and dust from all surfaces with an oil-free blast, or vacuum, immediately prior to application.

 

MIXING INSTRUCTIONS

Temperature of Product #19 must be 60 degrees F or above at time of mixing. Stir each component separately before blending. Mix 4 (four) parts by volume of Part A with 1 (one) part by volume of Part B for three minutes with a low speed electric drill motor equipped with a mixing paddle.

 

APPLICATION

BASECOAT: Product #19 can be applied with brush, roller, airless sprayer, squeegee, trowel, etc. . Apply a coat of #19 to surface to be finished, doing only a small area at a time, applying special sands to the surface of the wet resin.   Make sure that the entire surface is completely covered (no shiny spots visible). Allow them to dry. Then remove excess sand. An alternate method is to make a "dry" mortar by adding special sand and troweling in place.

TOPCOAT:. Apply a squeegee, roll, or spray coating of clear #19 to the surface of the basecoat if required.. If a smoother finish is required, the surface may be sanded and additional coat(s) of clear #19 applied.

 

LIMITATIONS

New concrete should be at least 28 days old. Temperature of substrate must be above 50 degrees F. DO NOT thin. For outdoor use contact Epoxy.com for technical assistance.

 

OPTIONAL FEATURES

  • INTEGRAL COVE BASE
  • MEDIUM, FINE, and SMOOTH TEXTURES

 

SAFETY PRECAUTIONS

Prolonged or repeated exposure may cause eye and skin irritation. If contact occurs, wash immediately and seek medical help. Use safety glasses with side shields and wear protective rubber gloves.

 

CLEANING

All tools and equipment should be cleaned before the system gels. Use MEK, Acetone, or any lacquer solvent.

APPLICATION PROPERTIES @77 DEGREES F
Viscosity (mixed) 950 CPS
Cure Time (Walk-on Traffic) 24 hours
Pot Life (200 gr.) 30-40 minutes
Cure Time (Truck Traffic) 48 Hours
Final Cure 7 Days
Packaging (unit size) 1.25 gal., & 5 gal, and drum Units.
PHYSICAL PROPERTIES (neat)
Adhesion to concrete ACI Committee 403 350 p.s.i (concrete fails)
Flexural Strength (ASTM D-790) 8000 p.s.i (7 days)
Compressive Strength (ASTM D-695) 11000
Absorption (ASTM D-670-63) 24 hour 0.1%
Adhesion to Metal 2500 p.s.i
Hardness (ASTM D-2240 80 (Shore D)
Tensile Strength (ASTM D-638) 8500 p.s.i
Elongation (ASTM D-638) 5.5%
Abrasion Resistance (ASTM C-501 35-40 mg loss (CS-17 wheel,
1 kg load, 1000 cycles)
Service Temperature (MIL-D-3134F) 160 degrees F. (immersion)
185 degrees F. (dry)
Impact Resistance (MIL-D-3134F) Withstands 16ft./lbs. no cracking
delamination or chipping
Indentation (MIL-D-3134F) Withstands 2000 lbs./square in.
for 30 min. without indentation
Elevated Temperature Resistance
MIL D-3134F
No slip or flow at required
temperatures at 158 F.

 

Chemical Resistance
Reagent Rating Reagent Rating
Acetic Acid -5%

L

Lactic Acid - 15%

R

Acetone

L

Methyl Ethyl Ketone

L

Bleach

L

Nitric Acid - 10%

R

Citric Acid - 30%

R

Skydrol

R

Crude Oil

R

Sodium Hydroxide - 50%

R

Diesel Fuel

R

Sulfuric Acid - 20%

R

Ethylene Glycol

R

Toluene

R

Fatty Acids

L

Urea R
Gasoline R Vinegar L
Hydrochloric Acid-15% R Xylene R
R=Recommended for Continuous Service L=Limited to occasional spills

Hit Counter

 

Exclaim

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over 300 products,
Since 1980
Florida & Vermont
USA

Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.

321-206-1833   Customer Service - Ordering and Order Status
                          Katey Fontaine, VP - Customer Service Director
                          sales@epoxy.com

714-657-3826  Technical Support
                         Norm Lambert, President - Technical Support Director 
                         info@epoxy.com
  
352-489-1666   Accounting and Administration
                          Debby Lambert, CEO, and CFO
                          office@epoxy.com 

352-489-1625   Fax line to all Departments
                         www.epoxy.com

24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253

MasterCard, Visa, and American Express logo

Copyright © 1994-2009 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.

This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.

Epoxy.com a division of Epoxy Systems, Inc.  warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months;  Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight  Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days.   Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com  within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com  SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.

Many of our products are made on an individual order basis.   Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater.  No returns on non-list priced items.  All Returns are for merchandise (store) credit only, no cash or credit card credits.  In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.

 

[Home] [Catalog of Products] [Where to Start] [[Bonding Systems] [Chip Floors] [Chemical Resistance]
[Coatings] [Conductive] [Applications] [Elastomeric Systems] [High Temperature]
[Industrial Floors] [Injection] [Joint Systems & Sealants] [Mortars / Grouts] [Novolac] [Polymer Systems]
[Primers and Sealers] [Misc.] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Installation Tips]
[Product Guide] [Wood Filler] [Who We Are] [Guide Specs]
[Tech Data Sheets in Acrobat Format ] [MSDS in Acrobat Format] [Online Ordering Authorization Form]


Hit Counter

 

Secure Login