Cold Temperature Cure Coating


[Home] [Catalog of Products] [Where to Start] [[Bonding Systems] [Chip Floors] [Chemical Resistance]
[Coatings] [Conductive] [Applications] [Elastomeric Systems] [High Temperature]
[Industrial Floors] [Injection] [Joint Systems & Sealants] [Mortars / Grouts] [Novolac] [Polymer Systems]
[Primers and Sealers] [Misc.] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Installation Tips]
[Product Guide] [Who We Are] [Guide Specs]
[Tech Data Sheets in Acrobat Format ] [MSDS in Acrobat Format] [Online Ordering Authorization Form]

 

Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980  

                                                   


Epoxy.com Product #1 Cold

100% Solids Cold Temperature Cure Epoxy Coating

Cures at Temperatures as Low as 35°F. Zero (0) VOCs so it MeetsLow VOC Requirements.


DESCRIPTION

Epoxy.com Product #1 Cold Temperature Cure Epoxy Coating is 100% solids and  specially formulated coatings for cold temperature applications. Able to cure at temperatures as low as 35°F. It is has Zero (0) VOCs. Since it has no VOCs, it has no solvent so it meets the strictest possible standard for a low VOC coating. It is often used in coolers and food preparation areas that require constant low temperatures. Product #1 Cold Temperature Cure Epoxy Coating is also frequently used in room temperature applications to meet super-fast cure, limited shutdown needs.

ADVANTAGES

  • Low temperature cure
  • Low odor during application and cure-will not taint foods
  • Superior stain and chemical resistance
  • Bonds well to cool, damp substrates
  • Zero (0) VOC- no VOC - No solvent  means it meets even the strictest low VOC standards
  • 100% Solids

CONSIDERATIONS

  • Substrate temperature must be a minimum of 35°F
  • Substrate must be free of dirt, waxes, curing agents, and other foreign materials

COMPOSITION

Epoxy.com Product #1 Cold Temperature Cure Epoxy Coating is 100% Solids Epoxy Resins and  Epoxy Hardeners

APPLICATION

SURFACE PREPARATION

Surface Preparation is the most critical portion of any successful resinous flooring system application. All substrates to receive Epoxy.com Product #1 Cold Temperature Cure COATING must be properly prepared. For more information see Epoxy.com Surface Preparation Guide and  Contact Epoxy.com Technical Service Department with your questions.

INSTALLATION

Installation of Epoxy.com Product #1 Cold Temperature Cure COATING is normally spread with with the "dip and roll" method or a notched trowel or squeegee and back-rolled with a medium or short nap roller. Care should be taken to minimize the entrapment of air caused by over-rolling.

CLEAN UP

Clean skin with soap and water. Tools and equipment should be cleaned with xylene or lacquer thinner.

COVERAGE

Epoxy.com Product #1 Cold Temperature Cure COATING is typically applied in two or more coats of 160-200 square feet per gallon per coat.

COLOR SELECTION

Epoxy.com Product #1 Cold Temperature Cure COATING is available in Light Grey, Sand, Old Gold, Mocha, Brick Red, Taupe, Dark Grey, Slate Blue, Colonial Green, Charcoal, Caramel, Gem Grey, White Sand, White, and Black. Safety Yellow, Deep Blue, Ivy, and custom colors available at an additional charge.

Epoxy.com Product #1 Cold cure Color Chart |100% Solids | Zero (0)VOC
Click the picture
of color card below  for a larger version of this picture of the color chart.
Please note:  The picture to the right is a photographic reproduction of the color card for this product.  The photo reproduction process and your monitor and/or printer will change these colors.  This chart is to give you an idea of the colors available and not intended for critical color selections.

TECHNICAL DATA

Viscosity @ 75°F 1,000 cps
Mixing Ratio 2 Parts A to 1 Part B by Volume
Solids Content 100%, by volume
Volatile Organic Content (VOC)0
Weight per gallon10.0-11.5 pounds per gallon, mixed

CURE/DRY TIME

Pot Life15 minutes @ 75°F
Dry to Touch2-3 hours @ 75°F; 14-16 hours @ 35°F
Re-Coat3-4 hours @ 75°F; 14-16 hours @ 35°F
Light Traffic5-6 hours @ 75°F; 24 hours @ 35°F
Full Cure & Maximum Resistance5 days

Other customers who visited this page also visited:

Hit Counter 

Exclaim

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over 300 products,
Since 1980
Florida & Vermont
USA

Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.

321-206-1833   Customer Service - Ordering and Order Status
                          Katey Fontaine, VP - Customer Service Director
                          sales@epoxy.com

714-657-3826  Technical Support
                         Norm Lambert, President - Technical Support Director 
                         info@epoxy.com
  
352-489-1666   Accounting and Administration
                          Debby Lambert, CEO, and CFO
                          office@epoxy.com 

352-489-1625   Fax line to all Departments
                         www.epoxy.com

24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253

MasterCard, Visa, and American Express logo

Copyright © 1994-2009 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.

This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.

Epoxy.com a division of Epoxy Systems, Inc.  warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months;  Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight  Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days.   Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com  within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com  SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.

Many of our products are made on an individual order basis.   Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater.  No returns on non-list priced items.  All Returns are for merchandise (store) credit only, no cash or credit card credits.  In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.

 

[Home] [Catalog of Products] [Where to Start] [[Bonding Systems] [Chip Floors] [Chemical Resistance]
[Coatings] [Conductive] [Applications] [Elastomeric Systems] [High Temperature]
[Industrial Floors] [Injection] [Joint Systems & Sealants] [Mortars / Grouts] [Novolac] [Polymer Systems]
[Primers and Sealers] [Misc.] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Installation Tips]
[Product Guide] [Wood Filler] [Who We Are] [Guide Specs]
[Tech Data Sheets in Acrobat Format ] [MSDS in Acrobat Format] [Online Ordering Authorization Form]


Hit Counter

 

Secure Login