Clear Casting Resin


[Home] [Catalog of Products] [Where to Start] [[Bonding Systems] [Chip Floors] [Chemical Resistance]
[Coatings] [Conductive] [Applications] [Elastomeric Systems] [High Temperature]
[Industrial Floors] [Injection] [Joint Systems & Sealants] [Mortars / Grouts] [Novolac] [Polymer Systems]
[Primers and Sealers] [Misc.] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Installation Tips]
[Product Guide] [WooWho We Are] [Guide Specs]
[Tech Data Sheets in Acrobat Format ] [MSDS in Acrobat Format] [Online Ordering Authorization Form]

 

Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980  

                                                   


Epoxy.com Product #214

100% Solids Epoxy Casting Tabletop and Bar Top Resin


GENERAL DESCRIPTION

Epoxy.com Product #214 is an all-purpose, low viscosity Epoxy System for coating wood and concrete counter tops, tabletops, bar tops and similar applications. Product #214 is commonly used as a clear self-leveling flooring material, where an extremely flat and level floor is required over concrete and wood.  Epoxy.com Product #214 is used extensively for ultra flat leveling of surfaces under equipment, where a very strong ultra flat bearing surface is a must.  It is also used successfully for ultra flat floors for stages, dance floor, and clean rooms.  Also used as a clear adhesive matrix for specialty colored glass and colored aggregate flooring and tiles. Product #214 forms a glossy, hard surface, which is resistant to stains. It is also used extensively as a water clear epoxy casting resin. Product #214 has excellent clarity and color retention. Epoxy.com Product #214 has zero (0) VOC making it essentially odorless and can therefore be used in occupied areas.

ADVANTAGES

Picture of Product #214 resin on a table top.
  • Low odor for use in occupied areas
  • Low viscosity - good wetting properties
  • Meets USDA standards for use in food handling applications
  • Glossy finish
  • Stain resistant
  • Zero (0) VOC - No VOC means it meets the toughest low VOC standards.

CONSIDERATIONS

  • Minimum application temperature of Normal Cure 50 Degrees F.
  • Substrate must be free of curing agents and any foreign materials.

SURFACE PREPARATION

Surface Preparation is the most critical portion to any successful epoxy application. All substrates must be properly cleaned and prepared. Substrate must be free of oil, paint, sealer, caulking, and all other contamination that will interfere with the bonding of this material. Please see Surface Preparation. Contact Epoxy.com for more details.

MIXING INSTRUCTIONS

Stir each component separately. Combine 2 parts A to one part B by volume into a clean container. Stir for three minutes, scrapping bottom and sides of container frequently. Do not add thinners.

APPLICATION PROPERTIES @77°F

Mix Ratio2:1 By Volume
Viscosity (mixed)950 CPS
Pot Life (200 gr.)30-40 minutes @ 70° F.
VOC 0
Cure Time (recoat) 10-14 Hours
Ultimate cure @ 74 Degrees F. 5 days
Color Clear
Packaging Unit Size 3 gallon units

Performance Properties

Tensile Strength ASTM D-638 8500 p.s.i
Elongation ASTM D-638 5.5%
Adhesion to metal 2500 p.s.i
Adhesion to concrete ACI Committee 403 350 p.s.i (Concrete fails)
Hardness ASTM D-2240 80 (Shore D)
Abrasion Resistance ASTM C-501 35-40 mg loss (CS-17 wheel, 1kg load, 1000 Cycles)
Service Temperature MIL-D-3134F 160 F (Immersion)
185 F (Dry Heat)
Impact Resistance MTI-D-3134F ss 4.7.3 Withstands 16ft/lbs no cracking,
delamination or Chipping.
Indention MIL-D-3134F ss 4.7.4 Withstands 2000 lbs./sq. in. for 30
minutes without indentation
Elevated Temperature Resistance
MIL-D-3134F ss 4.7.5
No slip or flow at required temperatures at
158 F.
Water Absorption ASTM D-670-63
(24 hour immersion)
0.10% maximum
Flexural Strength ASTM D-790 8000 p.s.i
Compressive Strength ASTM D-695 11000 p.s.i

APPLICATION

Will vary with application method. Be careful not to incorporate bubbles into the coating. If a second coat is desired, lightly sand the first coat, remove all dust, and then apply second coat.

SAFETY PRECAUTIONS

For industrial use only. Keep away from children. Refer to the Material Safety Data Sheets (MSDS forms) pertaining to this product before using. Avoid contact with skin or eyes. Prolonged or repeated exposure may cause eye and skin irritation. If skin contact occurs, wash immediately with soap and water. If contact with eyes occurs, flush eyes as required with clean water and seek medical help. Use safety glasses with side shields and wear protective rubber gloves.

CLEANING

All tools and equipment should be cleaned before the system gels. Use MEK, Acetone, or any lacquer solvent.

CHEMICAL RESISTANCE

Acetic Acid 5% L Lactic Acid- 15% R
Acetone L Methyl Ethyl Ketone L
Methyl Ethyl Ketone L Nitric Acid 10% R
Bleach L Sodium Hydroxide 50% R
Citric Acid 30% R Skydrol R
Crude Oil  & Diesel Fuel R Sulfuric Acid 20% R
Ethylene Glycol R Toluene R
Fatty Acids L Urea R
Gasoline R Vinegar L
Hydrochloric Acid 15% R Xylene R

R=Recommended for continuous service L=Limited recommendation, occasional spills.

Coverage: 231 cubic inches per gallon. At 1/8 inch thick 12.8 SF Per gallon. Use the calculator below to double check your estimate.

Material Calculator:

Square Footage
Thickness in Decimal Inches
 
Gallons of Material Required:

Exclaim

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over 300 products,
Since 1980
Florida & Vermont
USA

Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.

321-206-1833   Customer Service - Ordering and Order Status
                          Katey Fontaine, VP - Customer Service Director
                          sales@epoxy.com

714-657-3826  Technical Support
                         Norm Lambert, President - Technical Support Director 
                         info@epoxy.com
  
352-489-1666   Accounting and Administration
                          Debby Lambert, CEO, and CFO
                          office@epoxy.com 

352-489-1625   Fax line to all Departments
                         www.epoxy.com

24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253

MasterCard, Visa, and American Express logo

Copyright © 1994-2009 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.

This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.

Epoxy.com a division of Epoxy Systems, Inc.  warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months;  Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight  Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days.   Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com  within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com  SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.

Many of our products are made on an individual order basis.   Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater.  No returns on non-list priced items.  All Returns are for merchandise (store) credit only, no cash or credit card credits.  In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.

 

[Home] [Catalog of Products] [Where to Start] [[Bonding Systems] [Chip Floors] [Chemical Resistance]
[Coatings] [Conductive] [Applications] [Elastomeric Systems] [High Temperature]
[Industrial Floors] [Injection] [Joint Systems & Sealants] [Mortars / Grouts] [Novolac] [Polymer Systems]
[Primers and Sealers] [Misc.] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Installation Tips]
[Product Guide] [Wood Filler] [Who We Are] [Guide Specs]
[Tech Data Sheets in Acrobat Format ] [MSDS in Acrobat Format] [Online Ordering Authorization Form]


Hit Counter

 

Secure Login