Epoxy Coating


[Home] [Catalog of Products] [Where to Start] [[Bonding Systems] [Chip Floors] [Chemical Resistance]
[Coatings] [Conductive] [Applications] [Elastomeric Systems] [High Temperature]
[Industrial Floors] [Injection] [Joint Systems & Sealants] [Mortars / Grouts] [Novolac] [Polymer Systems]
[Primers and Sealers] [Misc.] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Installation Tips]
[Product Guide] [WooWho We Are] [Guide Specs]
[Tech Data Sheets in Acrobat Format ] [MSDS in Acrobat Format] [Online Ordering Authorization Form]

 

Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980  

                                                   

 


Epoxy.com Product #250

100% Solids Epoxy Coating


DESCRIPTION
Epoxy.com Product #250 Coating
is a 100% solids, moisture- insensitive epoxy coating, containing no solvents. It is ideal for non-potable water tanks, ponds, etc.  PRODUCT #250, mixed at a 2:1 ratio, produces a tough, chemical and abrasion-resistant coating for dry or damp concrete, wood or steel surfaces.

ADVANTAGES
Can be applied to concrete, wood or steel. The long pot life is an excellent advantage, particularly when temperatures are above 70°F. Epoxy.com PRODUCT #250 has excellent resistance to hydrogen sulfide.

PHYSICAL PROPERTIES

Color Gray—other colors are available as special order products
Viscosity (Brookfield Viscometer)
   #6 spindle @ 50 rpm
6,000 cps
Pot Life @ 72°F 45 mins (100 grams)
Tensile Strength
   ASTM D-638
5000 minimum (14 days)
Tensile Elongation
   ASTM D-638
7.5% (14 days)
Compressive Strength
   ASTM C 109 Mod.
7,500 psi (7 days)
Abrasion Resistance
   ASTM D 968
60 liters per mil min (14 days)
Dielectric Constant
   1 kiloHertz
   1 megaHertz
 
4.65
4.15
Dissipation Factor
   1 kiloHertz
   1 MegaHertz
 
0.0216
0.092
Volume Resistivity 8.1 * 1014 ohm-inches
Surface Resistivity 1.5 * 1015 ohms
Di-Electric Strength
   Volt per mil
440-465

SURFACE PREPARATION

Steel Surfaces: Steel surfaces should be abrasion blasted to commercial gray metal finish as specified by the Steel Structures Painting Council SSPC SP-6. All work blasted shall be coated the same day with Epoxy.com Product #1200 Zinc Rich Primer.

Concrete Surfaces: Concrete surfaces shall be cleaned to remove dirt, curing compounds, existing coatings or laitance to provide a clean, sound bonding surface. Cleaning may be accomplished with water blasting, abrasion blasting, or other method that would achieve a similar result.

MIXING
Stir Components "A" and "B" thoroughly before mixing. Combine two (2) parts by volume of "A" with one (1) part by volume of "B" (mixing ratio 2:1). Mix for not less than three (3) minutes with a slow speed drill (300 to 600 rpm), and an Epoxy.com Mixing Paddle.

APPLICATION
Epoxy.com PRODUCT #250
may be applied by brush, roller or spray. All spray equipment must employ traps to prevent water and oil from contaminating coating.

COVERAGE:
PRODUCT #250
will cover approximately 200 sq. ft. per gal. per coat at a thickness of eight (8) mils, dependent upon surface texture. For best results, use two (2) coats.

PACKAGING:
Epox.com PRODUCT #250
is packaged in three (3) gallon, and fifteen (15) gallon units.

LIMITATIONS:
PRODUCT #250
should not be applied when surface temperatures are below 40°F.

CAUTION:
WARNING! A Component contains epoxy resin. DANGER! "B" Component contains alkaline amines; strong sensitizer. May cause skin sensitization or other allergic responses. Use with good ventilation, particularly if material is heated or sprayed. Prevent all contact with skin or eyes. Wear protective clothing, goggles, gloves and/or barrier creams. Keep container closed when not in use. Wash thoroughly after handling.

FIRST AID:
In case of skin contact, immediately wash with soap and water. In case of eye contact, flush eyes with copious amounts of water for at least fifteen (15) minutes. Remove contaminated clothing and shoes. If irritation persists, seek medical attention. Wash clothing before reuse.

FOR INDUSTRIAL USE ONLY. KEEP AWAY FROM CHILDREN.

Exclaim

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over 300 products,
Since 1980
Florida & Vermont
USA

Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.

321-206-1833   Customer Service - Ordering and Order Status
                          Katey Fontaine, VP - Customer Service Director
                          sales@epoxy.com

714-657-3826  Technical Support
                         Norm Lambert, President - Technical Support Director 
                         info@epoxy.com
  
352-489-1666   Accounting and Administration
                          Debby Lambert, CEO, and CFO
                          office@epoxy.com 

352-489-1625   Fax line to all Departments
                         www.epoxy.com

24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253

MasterCard, Visa, and American Express logo

Copyright © 1994-2009 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.

This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.

Epoxy.com a division of Epoxy Systems, Inc.  warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months;  Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight  Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days.   Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com  within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com  SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.

Many of our products are made on an individual order basis.   Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater.  No returns on non-list priced items.  All Returns are for merchandise (store) credit only, no cash or credit card credits.  In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.

 

[Home] [Catalog of Products] [Where to Start] [[Bonding Systems] [Chip Floors] [Chemical Resistance]
[Coatings] [Conductive] [Applications] [Elastomeric Systems] [High Temperature]
[Industrial Floors] [Injection] [Joint Systems & Sealants] [Mortars / Grouts] [Novolac] [Polymer Systems]
[Primers and Sealers] [Misc.] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Installation Tips]
[Product Guide] [Wood Filler] [Who We Are] [Guide Specs]
[Tech Data Sheets in Acrobat Format ] [MSDS in Acrobat Format] [Online Ordering Authorization Form]


Hit Counter

 

Secure Login