Sprayable Polyurea Coating


[Home] [Catalog of Products] [Where to Start] [[Bonding Systems] [Chip Floors] [Chemical Resistance]
[Coatings] [Conductive] [Applications] [Elastomeric Systems] [High Temperature]
[Industrial Floors] [Injection] [Joint Systems & Sealants] [Mortars / Grouts] [Novolac] [Polymer Systems]
[Primers and Sealers] [Misc.] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Installation Tips]
[Product Guide] [Wood Filler] [Who We Are] [Guide Specs]
[Tech Data Sheets in Acrobat Format ] [MSDS in Acrobat Format] [Online Ordering Authorization Form]

 

Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980  

                                                   


Epoxy.com Product #312

Sprayable Aliphatic Polyurea Coating


DESCRIPTION

Epoxy.com Product #312 Aliphatic Sprayable Polyurea Coating is a two component sprayable aliphatic polyurea. It dries in seconds to provide a tough chemical and abrasion resistant coating. As an aliphatic polyurea, Epoxy.com Product #312 Aliphatic Sprayable Polyurea Coating  is color fast and will resist yellowing from Ultra violet light exposure. Typical working times of one minute or less can be expected. This fast reaction requires a fast, efficient mixing technique so that the mixture can be applied within the short gel times. Impingement mixing from available two-component spray machinery is efficient and entirely adequate.

Epoxy.com Product #312 Aliphatic Sprayable Polyurea Coating is recommended for use in areas such as tanks, cooling tower linings, water and wastewater and waterproof deck coatings. It can be used in food and beverage cold storage areas, mechanical rooms, industrial plants, chemical and fertilizer plants, pulp and paper mills and petrochemical facilities.

ADVANTAGES

bulletFast cure. Can be mixed and put in service within 2 hours.
bulletChemical and UV resistant.
bullet100% solids. Two-component, low shrinkage.
bulletExcellent physical properties including high adhesion, tensile strength and abrasion resistance.
bulletHigh thermal stability at temperatures up to 250° F.

PHYSICAL PROPERTIES

 
Mix Ratio By volume 1A to 1B
Drying Properties @ 30 mils wet @ 73° F and 50% RH  
Gel time, seconds 45
To touch 3 minutes
To recoat 3 minutes minimum;16 hours maximum
Surface at 1 hour tack free
Full Cure 24 hours
Elongation, % 750
Tear strength 500 pli
Shore D Hardness 54
Tensile strength, psi 2400
Remains flexible in temperature range of

-45oF to 200oF

Flash Point, Components >200° F
Gardner Impact Direct and Indirect >160 in-lbs
Moisture Vapor Transmission ASTM E 96

0.025 perm

Abrasion Resistance (wt. loss mg) ASTM D 4060

1000g 1000 rev CS-17 6 mg.
Color

White, Black, Light Gray, Dark Gray, Beige, Brick Red,

Bond Strength

 
Concrete 350 psi
Steel 1,500 psi
Wood 450 psi

SURFACE PREPARATION

Steel Surfaces – Prepare in accordance with Steel Structures Painting Council Surface Preparation SSPC-SP6 to SP10 near-white metal blast cleaning. All work blasted should be coated the same day.

New concrete - Remove laitance by acid etching, abrasive blasting or water blasting. Old concrete - abrasive blast or water blast to remove laitance and contamination. Spray apply one coat of Epoxy.com Product #810 Polyurea Primer to prevent pinholes

Polyurea – Less than three days old solvent wipe and apply Epoxy.com Product #312 Aliphatic Sprayable Polyurea Coating ; if more than 3 days old roughen surface with abrasive sanding. Solvent Wipe with Acetone or MEK and apply

Project Conditions: Surface must be structurally sound, dry, and uncontaminated. Concrete must be free of voids, bugholes, honeycombs and delaminations.

APPLICATION

For large volumes, a high-pressure proportioner with heated lines and an external impingement mix, two-component spray gun may be used. Epoxy.com Product #312 Aliphatic Sprayable Polyurea Coating  can be applied at temperatures from 35oF to 120oF.

The Gusmer Model H-V high-pressure proportioner and Gusmer Model GX-7 series with a 212 PCD and 453 mixing nozzle are recommended. Best spray pressure is 2000 to 3000 psi; hydraulic pressure at 400 - 550 psi. Materials are heated to 140 – 160° F for spraying. The use of conventional static mix or plural-component internal-mix spray equipment is not recommended. Thickness can be built to most specifications in one application. Best spraying practice is with gun 2 ft. from surface and perpendicular to surface. Edges left overnight should be roughened and primed before overlapping.

PACKAGING: Epoxy.com Product #312 Aliphatic Sprayable Polyurea Coating is packaged as a 100 gallon unit.

LIMITATIONS

Epoxy.com Product #312 Aliphatic Sprayable Polyurea Coating is an aliphatic based polyurea system. Consult chemical resistant chart for corrosive environment applications. Do not install in hydrostatic or moisture/vapor conditions.

SHELF LIFE: Six months minimum when stored at 75°F and dry conditions. Epoxy.com Product #312 Aliphatic Sprayable Polyurea Coating, like most construction materials, must be stored in a dry, well protected and suitable storage environment. Keep containers sealed.

CAUTION: Contains aliphatic isocyanates. Avoid breathing vapors. Avoid contact with skin and eyes. Do not ingest. Keep away from foodstuffs and wash thoroughly before smoking or eating. Should skin contact occur, wash skin well with soap and water. Should eye contact occur, flush thoroughly for at least 15 minutes with water. Get medical attention.

FOR INDUSTRIAL USE ONLY /KEEP AWAY FROM CHILDREN
Hit Counter

Exclaim

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over 300 products,
Since 1980
Florida & Vermont
USA

Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.

321-206-1833   Customer Service - Ordering and Order Status
                          Katey Fontaine, VP - Customer Service Director
                          sales@epoxy.com

714-657-3826  Technical Support
                         Norm Lambert, President - Technical Support Director 
                         info@epoxy.com
  
352-489-1666   Accounting and Administration
                          Debby Lambert, CEO, and CFO
                          office@epoxy.com 

352-489-1625   Fax line to all Departments
                         www.epoxy.com

24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253

MasterCard, Visa, and American Express logo

Copyright © 1994-2009 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.

This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.

Epoxy.com a division of Epoxy Systems, Inc.  warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months;  Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight  Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days.   Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com  within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com  SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.

Many of our products are made on an individual order basis.   Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater.  No returns on non-list priced items.  All Returns are for merchandise (store) credit only, no cash or credit card credits.  In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.

 

[Home] [Catalog of Products] [Where to Start] [[Bonding Systems] [Chip Floors] [Chemical Resistance]
[Coatings] [Conductive] [Applications] [Elastomeric Systems] [High Temperature]
[Industrial Floors] [Injection] [Joint Systems & Sealants] [Mortars / Grouts] [Novolac] [Polymer Systems]
[Primers and Sealers] [Misc.] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Installation Tips]
[Product Guide] [Wood Filler] [Who We Are] [Guide Specs]
[Tech Data Sheets in Acrobat Format ] [MSDS in Acrobat Format] [Online Ordering Authorization Form]


Hit Counter

 

Secure Login