Epoxy.com Product #407 Elastomeric Urethane Traffic bearing Membrane

Skip Navigation Links

[Home] [Catalog of Products] [Where to Start] [[Bonding Systems] [Chip Floors] [Chemical Resistance]
[Coatings] [Conductive] [Applications] [Elastomeric Polyurethane Systems] [Garage Floor] [High Temperature]
[Industrial Floors] [Injection] [Joint Systems & Sealants] [Mortars / Grouts] [Novolac] [Polymer Systems]
[Primers Sealers] [Misc.] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Installation Tips]
[Product Guide] [Wood Filler] [Who We Are] [Guide Specs]
[Tech Data Sheets in Acrobat Format] [MSDS in Acrobat Format] [Online Ordering Authorization Form]

 

Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980

Epoxy.com Product #407

Aliphatic Traffic Bearing Membrane


DESCRIPTION:

Epoxy.com Product #407 Aliphatic Traffic Bearing Membrane is a two component, ultra high solids aliphatic polyurethane elastomeric membrane. Epoxy.com Product #407, when applied, is resilient and accommodates movement in concrete substrates. Epoxy.com Product #407 is used as a top coat traffic bearing membrane or non-skid coating that retains color and physical properties when exposed to harsh UV conditions. Epoxy.com Product #407 is used as a system with Epoxy.com Product #882, and may be applied as the top coat on Epoxy.com Product #409 to maximize cost effectiveness. Epoxy.com Product #407 cures at ambient temperatures and is impermeable to moisture, oils, mild acids, gasoline, and alkalies.

ADVANTAGES:

  • Pre-weighed units
  • Used for UV stability on Epoxy.com Product #409 and other membranes
  • Ultra high solids content
  • Protects concrete surfaces from deterioration caused by water intrusion and wet/dry or freeze/thaw cycles.
  • Exhibits excellent shear and tear strength.
  • Will withstand temperature extremes from -20°F to 180°F.
  • Cold applied

SYSTEM DESCRIPTION:

Pedestrian Grade - Recommended DFT of System 27.0 to 34.0 mils DFT.

Primer - One Coat Epoxy.com Product #882 at 3.0 to 4.0 mils WFT to achieve 3.0 to 4.0 mils DFT.

Intermediate - One Coat Epoxy.com Product #409 or Epoxy.com Product #407 at 12.0 to 15.0 mils WFT to achieve 12.0 to 15.0 mils DFT.

Finish - One Coat Epoxy.com Product #407 at 12.0 to 15.0 mils WFT to achieve 12.0 to 15.0 mils DFT.

The use of rounded silica sand is recommended to produce an anti-slip or non-skid finish.

Traffic Grade - Recommended DFT of System 53.0 to 64.0 mils DFT.

Primer - One Coat Epoxy.com Product #882 Primer at 3.0 to 4.0 mils WFT to achieve 3.0 to 4.0 mils DFT. (lightly seed while wet with a rounded 16 / 30 silica).

Intermediate - One coat Epoxy.com Product #409 or Epoxy.com Product #407 at 25.0 to 30.0 mils WFT to achieve 25.0 to 30.0 mils DFT. (broadcast while wet with a rounded 20 / 40 silica at a rate of 1/4 to 1/2 pound per square foot).

Finish - One coat Epoxy.com Product #407 at 25.0 to 30.0 mils WFT to achieve 25.0 to 30.0 mils DFT.

PHYSICAL PROPERTIES:

Pot Life @ 75°F

20 min/ 1 gal mixed material

Cure Time @ 75°F

6 hrs. - foot traffic
24 hrs - vehicle traffic

V.O.C. content

0.15 lbs per gallon

Hardness - Shore A
   (ASTM D 2240)

80

Tensile Strength, 7 days

1,500 psi

Elongation, 14 days

300% minimum

Pull-Off Test
   (ASTM D 4541 - 85)

Failure in concrete substrate
650 psi

Shelf Life

Six (6) months

SURFACE PREPARATION:

Steel: Prepare in accordance with SSPC-SP6 (Commercial Blast) or SSPC-SP10 Near White Metal Blast. All work blasted should be coated the same day. Apply Epoxy.com Product #1200 Zinc Rich Primer to prepared steel. Follow application guildelines on Product #1200  technical data sheet. Allow Product #1200 to cure a minimum of four (4) hours at 70°F and not to exceed a maximum of 48 hours at 70° F prior to application of Epoxy.com Product #407.

Concrete: All concrete must be cured a minimum of 28 days. All concrete must be clean, sound, dry, free of oils and other bond inhibiting contaminants. Air and substrate temperature shall be 40°F and rising. Mechanical surface preparation such as shot blasting, abrasive blasting or hydro blasting is required to produce a clean and lightly profiled or textured surface. If hydro blasting is used, allow 24 to 48 hours for concrete to dry completely. Apply Product #882 to prepared concrete. Allow Product #882 to dry a minimum of two (2) hours at 70°F and not to exceed a maximum of 36 hours at 70°F prior to application of Epoxy.com Product #407.

MIXING:

Stir "A" component prior to mixing or combining with "B" component. Mix material to the proper ratio, 4A to 1B with a mixing paddle and slow speed drill for a minimum of two (2) minutes until thoroughly mixed. Avoid entrapping air while mixing.

APPLICATION:

Primer - After mixing Product #882 Primer apply by brush, roll, or airless spray at 3.0 to 4.0 mils WFT to achieve 3.0 to 4.0 mils DFT. While Product #882 Primer is still wet lightly seed with rounded 16 / 30 silica sand. Allow to dry a minimum of two (2) to four (4) hours at 70°F or until tack free prior to application of Epoxy.com Product #409 or Epoxy.com Product #407 Intermediate Coat.

Intermediate - After mixing apply Epoxy.com Product #409 or Epoxy.com Product #407 by straight or notched squeegee at appropriate WFT to either pedestrian or traffic grade application to achieve the appropriate DFT for the application. After the squeegee application, back roll with a 1/2 inch to 3/4 inch nap roller cover. Follow this procedure with a spiked roller cover to insure no air bubbles are present. Broadcast the rounded 20/40 silica sand at a rate of 1/4 to 1/2 pound per square foot. Allow the Epoxy.com Product #409 or Epoxy.com Product #407 Intermediate Coat to dry approximately 8 hours prior to application of finish coat.

Finish - After mixing apply top coat of Epoxy.com Product #407 by straight or notched squeegee at appropriate WFT for either pedestrian or traffic grade application to achieve the appropriate DFT for the application. After the squeegee application back roll with a 1/2 inch to 3/4 inch nap roller cover. Follow this procedure with a spiked roller cover to insure no air bubbles are present. Allow the Epoxy.com Product #407 Finish Coat to dry a minimum of 6 hours at 70°F for foot traffic and a minimum of 24 hours at 70° F for vehicular traffic.

LIMITATIONS:

Thinning may result in loss of adhesion of cured materials and promote rapid deterioration of protective properties. Do not apply either Epoxy.com Product # 882 Primer, Epoxy.com Product #409 or Epoxy.com Product #407 on wet surfaces or below 40°F. Product #409 is not UV Resistant. Epoxy.com Product #407 should be used as a top coat if UV Resistance is required.

PACKAGING:

Epoxy.com Product # 882 - available in 2 gallon and 10 gallon units.

Epoxy.com Product #407 - available in 1 gallon and 5 gallon units.

STORAGE:

Product #844 and Epoxy.com Product #407 shall be stored in a dry protected area at temperatures between 60°F and 90°F. Do not allow to freeze.

CAUTION:

Epoxy.com Product #407 contains organic isocyanates. Avoid contact with skin and eyes. Do not ingest. Keep away from food stuffs. Wash thoroughly prior to smoking or eating. Should skin contact occur, wash skin well with soap and water. Should eye contact occur, flush thoroughly with water for at least 15 minutes. Seek medical attention immediately.

FOR INDUSTRIAL USE ONLY. KEEP AWAY FROM CHILDREN.

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over 350 products,
Since 1980
Florida & Vermont
USA


Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch

321-206-1833   Customer Service - Ordering and Order Status
                          Katey Fontaine, VP - Customer Service Director
                          sales@epoxy.com

714-657-3826  Technical Support
                         Norm Lambert, President - Technical Support Director 
                         info@epoxy.com

352-489-1666   Accounting and Administration
                         Debby Lambert, CEO, and CFO
                          office@epoxy.com

352-489-1625   Fax line to all Departments
                          www.epoxy.com

24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253

We accept Mastercard, Visa and American express

Copyright © 1994-2009 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.

This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.

Epoxy.com a division of Epoxy Systems, Inc.  warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months;  Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight  Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days.   Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com  SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.

Many of our products are made on an individual order basis.   Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater.  No returns on non-list priced items.  All Returns are for merchandise (store) credit only, no cash or credit card credits.  In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.


[Tech Data Sheets in Acrobat Format] [MSDS in Acrobat Format] [Online Ordering Authorization Form]