EpoxySystems Product #680 Polymer Concrete methyl methacrylate (mma) reactive resin is used as a binder to develop polymer concrete which produces extremely high strength and chemical resistance with an abrasion resistant surface. EpoxySystems Product #680 is prepackaged and preproportioned for easy mixing and placing at the job site. The liquid polymer and the preproportioned hardener filler is mixed either in the polyethylene bag or in a mortar mixer.
Â· May be used in temperatures as low as 15Â°F (-9.5Â°C) to a depth of 1â€ (24.5mm).Thinner sections such as 1/2â€ (12.7mm) or 1/4â€ (6.35 mm) will take longer to set. EpoxySystemsâ€™ pot hole patching or thicker overlays, 3/8â€ or 1/8â€ dry aggregate may be added for economy. (Depending on requirements 50% to 100% aggregate.)
Â· Mixes easily; no tools required. It is preproportioned, eliminating measuring the many components incorporated to produce polymer concrete.
Â· Can be used year round at temperatures as low as 15Â°F (-9.5Â°C)
Â· Has high compressive, flexural, and tensile splitting strengths.
Â· May be applied as thin as 1/4â€.
Â· Is not affected by freeze-thaw cycles and is chemically resistant to sulfates, deicing chemicals, and acids.
Â· Cure time is 45 minutes to 2 hours. It produces 10,000 to 12,000 p.s.i, depending upon ambient temperatures.
Â· Tools, such as trowels, can be cleaned in liquid polymer (supplied as Component A) or EpoxySystemsâ€™ Tool and Equipment Cleaner.
Â· Patching and overlays can be accomplished even in winter months.
The following properties were
achieved Â® 70Â°F Â± -2Â°F (21Â°C)
(Symbols: + - resistance, Â± = limited resistance, - = not resistant)
All laitance, grease, curing compound residue, or any other contaminants must be removed by either sandblasting, wire brushing, or any other suitable means. Areas to receive EpoxySystems Product #680 must be dry.
For best results, EpoxySystems Product #681Primer should be used. To prime surface, mix Component A and Component B (white initiator) and apply to the prepared surface by brush or roller. Apply primer at the rate of 50-100 SF (9.29 m2) per gallon, depending on porosity of surface. (Weight of mixed primer is 8.4 lbs. Â± .2 lbs/gallon.)
Pour Component A (liquid mma) into polyethylene bag containing Component B (hardener filler).
Place material into area to be patched. Finish with wood float, steel trowel, or screed.
A 68# unit (30.91 kg) EpoxySystems Product #680 will yield 1/2 cubic foot which will cover 15.2 SF at 3/8â€ (9.53 mm) thick, neat.
EpoxySystems Product #681 PRIMER PACKAGED FOLLOWS: Component A (liquid mma) in 1/2 gallon, 1 gallon, and 5 gallon containers.
EpoxySystems Product #680 POLYMER CONCRETE is packaged in a 68# Unit consist of 1 gallon Component A (liquid MMA) and a 60# polyethylene bag of Component B (Hardener filler)
Areas receiving EpoxySystems Product #680 must be well ventilated. Surfaces to receive EpoxySystems Product #680 must be DRY. The material has a limited shelf life of 2 to 4 months in originally sealed cans.
Component A is highly flammable. Do not use near open flame or while smoking. Avoid contact with skin. Component B (initiator) is shock sensitive. Keep away from light.
USE UNDER CONDITIONS OF VENTILATION.
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have.
For more information please contact:
Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
321-206-1833 Customer Service - Ordering and Order Status
352-489-1625 Fax line to all
24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.
This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.
Epoxy.com a division of Epoxy Systems, Inc. warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.
Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
[Home] [Catalog of Products]
[Where to Start] [[Bonding Systems]
[Chip Floors] [Chemical Resistance]