Epoxy.com Product #714
Precast Segmental Epoxy Adhesive
Epoxy.com PRODUCT #714 Precast Segmental Adhesiveis a 100% solids, gelled epoxy adhesive formulated to the requirements of ASTM C-881-90, Type VI, Grade 3, Class D, E, or F. AASHTO M-235-90 duplicates the technical requirements of ASTM -C-881-90.
PRODUCT #714 Class D - Use in temperatures * of 40oF to 65oF.
PRODUCT #714 Class E - Use in temperatures * of 60oF to 80oF.
PRODUCT #714 Class F - Use in temperatures * of 75oF to 90oF.
* Concrete Surface Temperature
WHERE TO USE
Concrete Surfaces:Concrete surfaces shall be cleaned to remove dirt, curing compounds, coatings or laitance to provide a clean, sound bonding surface. Cleaning may be accomplished with Epoxy.com Masonry Cleaner and 5,000 psi minimum waterblasting, abrasive blasting, or other methods that achieve an acceptable result. Surfaces should be dry at time of application of PRODUCT #714.
Use PRODUCT #714 Class D, E, or F according to the concrete surface temperature at the time of installation. Combine one part by volume "A" with one part by volume of "B" (mixing ratio 1:1). Mix for not less than three minutes, using a slow speed drill, (300 to 600 rpm) and an Epoxy.com Mixing Paddle. Apply immediately after mixing.
PRODUCT #714should be applied within the first half of its gel time, so that there is adequate time left within the open time of the adhesive for closure and temporary post-tensioning to specification values. If the segments are not jointed within 70% of the PRODUCT #714 open time, operations should be halted, the PRODUCT #714 removed, and fresh PRODUCT #714 applied. Apply PRODUCT #714 on both segments to be joined to a minimum uniform thickness of 1/16", or to the fixed segment face to a minimum uniform thickness of 1/8", using
trowel, brush, or gloved hand. A discernible bead line of PRODUCT #714 should be observed on all contact areas after closure and initial post tensioning. After the segments have been joined, excess PRODUCT #714 should be removed from the joined surfaces where accessible. Tendon ducts should be swabbed immediately after stressing, to remove or smooth any epoxy in the conduit, and to seal surface pockets or bubble holes that have formed.
231 cubic inches per gallon. One (1) mixed gallon will cover 3696 square inches, 1/16" thick, or 1848 square inches, 1/8" thick.
PRODUCT #714is available in two (2) gallon and ten (10) gallon units.
"A" Component contains epoxy resin. DANGER! "B" Component contains alkaline amines; strong sensitizer. May cause skin sensitization or other allergic responses. Use with good ventilation, particularly if material is heated or sprayed. Prevent all contact with skin or eyes. Wear protective clothing, goggles, gloves and/or barrier creams. Keep container closed when not in use. Wash thoroughly after handling.
FIRST AID: In case of skin contact, immediately wash with soap and water. in case of eye contact, flush eyes with copious amounts of water for at least fifteen (15) minutes. Remove contaminated clothing shoes. If irritation persists, seek medical attention. Wash clothing before reuse.
FOR INDUSTRIAL USE ONLY / KEEP AWAY FROM CHILDREN
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have.
For more information please contact:
Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
321-206-1833 Customer Service - Ordering and Order Status
714-657-3826 Technical Support
352-489-1625 Fax line to all
24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.
This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.
Epoxy.com a division of Epoxy Systems, Inc. warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.
Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
[Home] [Catalog of Products]
[Where to Start] [[Bonding Systems]
[Chip Floors] [Chemical Resistance]